Fermentation Update

This pic taken last night shows fermentation progress after ~24hours (48 hours for the hefe).  They are going crazy!

It reminds me of the Buffalo Wild Wings commercial.  Haha, no bratwurst in these brews though.

Again, clockwise from left: Munich Commoner, Matrimony Mild (doesn't seem like I will need the blow-off hose after all, Matrimony Wine, and Steinau Weissbier.  The towels around the carboys help prevent excessive light exposure which apparently stresses active yeast.

Hefe, Parti-Gyle, and SMaSH!

This weekend was a crazy brewing weekend.  I had promised a friend, Tom, that I would brew a Hefeweizen with him, which we decided to brew Friday night.  We seemed to have hit all our metrics but I decided to just pitch a vial of yeast (if the vial were super fresh I'd probably be ok, but it was a couple of months old).  We will see how it affects fermentation.  I didn't take any pictures of the happenings mainly because I didn't feel like it.

Saturday morning I awoke at 6am.  I had a parti-gyle mash to do.  For those of you who don't know what that is and want more details on it, look here.  For the broad strokes, its an old fashioned approach to brewing which gets more sugars out of the grain.  You can have a big batch of grain and make two beers from it that, on average, might be slightly stronger (more sugary) than if you brewed the two batches completely independent of one another.  Sometimes that always doesn't work out.  Today it is primarily used as a way to make a really strong beer and then a weaker beer.

I've wanted to brew a Barleywine for our wedding reception (which is less than 6 months away!!) but my current system does not allow me to efficiently make high gravity beers (for the record, in this post when I make any reference to 'efficiency' I am basically talking about the amount of sugar extracted from the grain. A fixed amount of grain has a maximum amount sugar it can yield.  So my meaning of efficiency within this post is how close I am getting to the maximum theoretical yield).  So I thought that if I added a few more pounds of grain I could do a parti-gyle mash where I collect 7 gallons worth of first runnings for my barleywine, and then batch sparge with another 7 gallons of hot water to further rinse the sugars from the grain and yield a second, smaller, batch of beer. So...

For Mark and Amber's wedding I made a batch of 'Matrimoniale' that I actually was quite proud of.  Working loosely off that recipe, I made my recipe (spoiler alert for those of you who thought I would keep my brews a surprise):

20# American 2-row
4# Munich
4# Wheat
1.5# Crystal 20L
1.5# Crystal 90L
0.5# Crystal 120L

Mashed at 151F for an hour.  Remember, this is a parti-gyle mash.  So my first running gave a corrected starting gravity of 1.086.  This yielded an OG right around 1.100.  Here were the other details for the brew:

2.7 oz. Northern Brewer (10.5%AA) at 60min
1.5oz  Chinook (11.8%AA) at 10min
1.5oz Willamette (4.7%AA) at 10min
1.5oz Chinook at 0min
1.5oz Willamette at 0min

20grams of Safale US-05 dry yeast, rehydrated.

On the second runnings I was a little lower than I had hoped, but not terribly so.  The corrected starting gravity on the second batch was right at 1.039.  This gave an OG right around 1.046.  Here were the details for this smaller batch.

0.7 oz. Northern Brewer at 60min
0.3oz Chinook at 10min
0.3oz Willamette at 10min
0.4oz Chinook at 0min
0.4oz Willamette at 0min

9grams of Safale US-05 dry yeast, rehydrated.

Basically, the smaller gravity batch is a teaser for the barleywine.  I will ferment both and save the Barleywine til the wedding.  The smaller brew I will probably be drinking here very soon.  I hope it turns out.

Here are some pics of the process:

The grains. No water yet.  Mash tun is almost full!

Protein rest.  I had to do two infusions because otherwise I would have been trying to lift 11 gallons of hot water up to pour it in the tun.

And it's a good thing I did two infusions.  Turns out I overestimated the size of my mash tun and ran out of room for strike water.  SO to get to my target mash temperature I had to pull a decoction.  It was a short decotion, just enough to raise the temp in the main tun another 10 degrees.

Temperature has been obtained!

First runnings.  Tough to see but it's a pretty good color.  Nice burnt orange even in the thin tube.

Hop Spider getting it's first workout.  It has seemed to have passed with flying colors!

Racking to the fermentor.  I was happy with the color.

The hop turd from the spider.  Put it with my cascades.

Second runnings.  Very close in color to the first runnings.  Obviously, just a little lighter.

We got our first frost last night.  I thought the ice crystals on the rearview mirror were really neat.  They were standing straight up.

So after a 9 hour parti-gyle session I decided to brew another small 2 gallon batch of what the homebrewing community calls a SMaSH (single malt, single hop).  The purpose of a smash is to isolate a malt and/or hop to better learn it's characteristics so that you can make educated decisions on how to formulate recipes with more complex malt and/or hops bills.

My local homebrew club has monthly meetings with little mini club competitions.  Each month we pick a style or ingredient or spice/flavoring to add to a beer for the meeting two months in advance.  Brewers who are intrigued can partake and bring their brew to that meeting to go against other brewers.  So December's competition is SMaSH beers.  In the US, a lot of SMaSH beers are lighter malt varieties with high alpha-acid american hop varieties.  I decided I wanted to meet somewhere in the middle.  Loving german malts and american hops I decided to make my SMaSH out of Munich Malt and Northern Brewer hops.  Here's my recipe (for 2 gallons):

4# Munich
 Mash at high 140s for 60min

0.2oz Northern Brewer at 60min
0.2oz Northern Brewer at 10min

4 grams of rehydrated Safale US-05.   Sorry no pics for this brew, just wanted to knock it out.
I hope it turns out well and does well for me at the competition.

As you can see from this posting, I've kinda gone 'all-in' with the dry yeast.  It will either be genius or bite me in the a$s.  I plan to at least live to tell the tale.  That's all for this posting.  Below is one last pic of all carboys filled up this weekend.  17 gallons of brew!

Clockwise from left: 2gal Munich Commoner, Matrimony Mild?, Matrimony Wine, Steinau Weissbier

I obviously enjoy brewing.  But 17 gallons in 30 hours is a lot!

The Itsy Bitsy HopSpider Crawled into a Brewkettle

This will be a quick one folks.  This is a "hopspider":

It's purpose is to allow full hop utilization in the brew kettle while still allowing for hop sludge and cones to be removed easily from the wort after the boil.  I stumbled upon this on the homebrewing forums while researching other stuff.  I though, 'Gee, why didn't I think of that?'  It's so simple and functional (though I have yet to test it).  With $10 in parts from the hardware store and 5 minutes of easy labor, it's ready to work.  Here's what you need:

(1) 4" to 3" PVC reducing union
(1) 3-4" worm clamp ( I think that's the size...just feel it up in the store to be sure)
(1) 5 gallon paint strainer (I had to buy a 2pk, and you may have to also)
(3) 5/16" x 8"L carriage bolts
(3) 5/16" locking washers
(3) 5/16" flat washers
(6) 5/16" hex nuts

Construction is very easy, as long as you have a drill.  On the 3" side of the PVC union drill three holes 120degrees apart and about 3/4" down from the top.  I started with 3/16" pilot holes and then finished with 5/16" holes.  Install worm clamp on 3" side of the union below the drilled holes.  Assemble bolts into holes using a hex bolt, followed by the flat washer, followed by a pvc hole, followed by a locking washer, followed by another hex nut.  Do this at each PVC hole.  Finally feed the paint strainer bag over the outside of the 4" side of the union and then tuck it under the worm clamp on the 3" side and tighten down the worm clamp (if you worm clamp the bag on the 4" side a heavy hop bag from will 'pull' off the clamp and your bag will fall into your kettle.)

That's it!

Here's a close up of the finer points on the spider:

A pic of the spider in the kettle:

These come in handy for hoppy hoppy beers and I have read that utilization is not affected because the bag is so big that the hops basically swim free.

I will be testing it this weekend when I brew one of my wedding brews this weekend.  I'm gonna need it because the boil is going to have 9 oz. of hops.

I would highly recommend this project to any brewing friends.  It is very easy and highly praised by others who have done it.

Some might ask, 'Does the PVC cause any concern for plasticy flavors from it sitting over a steamy kettle?  Do the carriage bolts (zinc coated steel, not stainless) possibly rust up and cause issues?'

The answers are no and maybe.  No one who has used one has reported issues of plastic flavors from the strainer or union.  Though the bolts are basic steel, they are also very cheap.  If I ever see issues of rusting I'll just replace them.

Stay tuned for a report on how it works!

Oktoberfest Party 2012

My brewing hobby of 2012 has allowed my to brew a lot different styles and utilize a lot of different brewing-methods.  The highlight of my brewing year has to of been back in March when I brewed a double decocted all grain Oktoberfest.  It was a long and tiring brew day, and I barely got to taste the beer before this past weekend.  You see, I was saving it for a special party, Ashley's and my inaugural Oktoberfest!

For the event I brewed two batches of Oktoberfest, a Raspberry Hefeweizen, and a Belgian Dubbel.  20 gallons in total.  I wanted to share these brews with my brewthers and brewisters before the party.  Sadly they could not be in Arkansas for the party so I sent them some samples and we had a google hang-out a few nights ahead of time.  After drawing the samples, I was probably down to about 17 gallons of brew, or just a little more than a full sized keg.

This party also served as an event to officially break-in my kegerator.  If you remember, I got this kegerator over a year ago.  While it has served me well in holding many bottles of beer and also being a great fermentation chamber, I had yet to serve any brews from the classy brass draught tower.  So all my Oktoberfest offerings were kegged for this momentous occasion.

Ashley and I had a lot of fun (and a little stress) doing all the prep-work for this party.  We wanted the house to be very welcoming, the food to be tasty, and beer to be perfect.  We re-arranged the living room to open up the space a lot more, de-cluttered, and got everything cozy.  We made fresh baked soft pretzels, German potato salad, beer dip, pumpkin dip, pigs-n-a-blanket, chips and salsa, etc.  Friends brought chili cheese dips, casseroles, sauerkraut, dessert cakes, and festive spirits.  I had Thurn's Specialty Meats out of Columbus, OH air-mail me some delicious bratwursts for the grill.  Ashley made a tasty Sangria for those not to keen on brew, and I made a quick batch of root beer for all the kids who would be at the party.

The party kicked off around 3pm and went for several hours.  The homebrew and food was very well received.  We kicked both kegs of Oktoberfest and put serious dents in the RaspHefe and Belgian kegs.  Though originally thinking we had way too much food, there was very little left behind when all was said and done.

It was really a great party and all the pre-work leading up to it was certainly worth while.  Though we missed being able to party with our distant friends and family, we were grateful for all the locals who came and helped us eat and drink and celebrate a wonderful Oktober.  All for now, enjoy the pics!

The google hang-out veering off-course as usual.

House Outside Compliments of Ashley

House Inside also Compliments of Ashley, though we
picked the couch and rug together!

Mercedes woke up ready to party.

Mixin the pretzel dough

Pretzels formed

Pretzels baked

Sangria fruit ready for some wine

One of Ashley's best friends, Lara, came to party from OK city.

Raspberry Hefeweizen (ended up being a little to Razzy...almost like a wine cooler).

My good friend, Dustin, enjoying a liter of Muhleisen Extract Oktoberfest

And that right there is a liter of Muhleisen Hochkurz Double Decocted All Grain Oktoberfest.  I was really happy with how this one turned out.

MHDDAGO in the boot (for me) and a friend's MEO liter half gone.

The pretzels were really very tasty and all 36 disappeared pretty quick.

Nathaniel, a crazy Aussie, exemplifies the joy of the Oktoberfest party.

The vinyls only turned for about 15 minutes because I drank too much and didn't stay on top of it.

Engagement Party

So, we are a couple of weeks behind posting this but we wanted to write a quick couple of paragraphs about our engagement party.  The party was hosted by Ashley's mum, Pam, and her matron-of-honor, Maggie.  Festivities went down at Pam's house which is an ideal home for entertaining.  Pam and Maggie really out did themselves with all of the delicious food and decorating.  Everyone who showed up just stuffed themselves on everything from individual 7-layer dip cups to homemade beef jerky.

Not wanting to add to Pam or Maggie's stress, but desiring a decent beer spread, I volunteered to make the beer buying round.  My only requirement was cans because empty glass bottles in bulk make for a much heavier trash bag in the morning.  Luckily several craft breweries now release beer in cans.  The spread was 50/50 with the big three (Miller, Cooers, Bud, all light) sharing the stage with craft and smaller macro breweries (Shiner, Fat Tire, Avery).  For the non-beer drinkers, Pam and Maggie made a couple of delicious Sangrias for the red wine and white wine fans.

We are grateful for everyone who showed their support and were able to come celebrate with us!  We are also thankful for the awesome hostesses Pam and Maggie.  We look forward to April, 20th of 2013 and hope everyone that follows this blog can make it NWA for a celebration!

Enjoy the pics.  I was outside tending the beer cooler and didn't think to take a single pic all night.  As you can see, the people inside had a better mind to snap some shots.

The Spread

The coozies

Ashley with some of her employees (Left to Right: Whit, Lex, Ashley, Shelby, and Michayla [?SP?])

Matron-of-honor Maggie w/ Ash

Pamfab and Ash

Hostesses Maggie and Pam getting lovee-dovee with Ash

Ash with Matt Mulehorn (that's me)

Ash and Casey

Little cakes, they were good.

The centerpiece with all the food around it.

Another food shot.  The 7-layer dip cups were tasty.